|
Products:
Fiberglass Casement Windows - Product
Description
Features • Product Description • Thermal Performance
Available Sizes
• Vertical Section
• Horizontal Section • Mullion
details
Photo Gallery
PERFORMANCE
CAN/CSA-A440-M90
| Air Leakage fixed |
Fixed |
( 0.080 (m 3/h)/m )
( fixed < 0.25 (m 3/h)/m)
|
| Water Leakage |
B6 |
( 600 Pa = 110 km/h )
approx 12 lbs/ft^2 |
| Wind Load C3 |
C3 |
(passed 3000 Pa blowout
approx 63 lbs/ft^2 |
CAN/CSA-A440.1-M91
Energy Rating up to +6 W/m^2K
These characteristics exceed the requirements for NWDA’s Grade 60.
FRAME & SASH
Fiberglass profiles are made from more than 60% glass fibres. The balance is polyester resin and performance additives. The glass fibres are made by spinning melted silica sand. The thermoset polyester resin is based on a petroleum derived alkide. The frame and sash are insulated with expanded polystyrene. Frame corners are assembled with foam filled glass reinforced nylon corner keys. Standard frame depth is 3 ¼”. For door sidelites and transoms, as well as windows with mullions between large glass areas, use the optional 4 ½” frame.
Back to
the Top
BRICKMOLD
Extruded aluminum brickmolds are available with and without integral installation flanges.
Back to
the Top
FINISH
All exposed portions of the fiberglass profiles are painted. Standard finish is Grafted Coatings’ KTM-4. This water borne acrylic/urethane meets AAMA 613-96 and 615-96 (draft). All profiles are stocked in white. Custom colours are available. Also available is a real red oak or hard maple veneer interior.
Back to
the Top
JAMB EXTENSIONS
Wood jamb extensions are available in many depths and species, including pre-primed, veneer wrapped strawboard and ‘river bottom pine’.
Back to
the Top
HARDWARE
A Truth ™ Dyad (split-arm) operator is standard. It has a high pressure die cast zinc case, crank handle and knob. The handle operates a hardened steel drive worm and gear arm. A zinc die cast single lever multi-point lock is standard. Standard hardware colours are white, beige and brushed chrome. Heavy duty concealed hinges allow 90 degree opening. Egress hinges and easier wash hinges are available.
Back to
the Top
GLASS
The insulating glass conforms to CAN/CSGB-12.8-M90. Minimum glass thickness is 3mm or 1/8” (double strength). Both double glazing (20mm or ¾” overall thickness) and triple glazing (34mm or 1 5/16” overall thickness) are available. All glazing is dual sealed and made with Edgetech’s SuperSpacer ™. Glass thickness is determined by the National Building Code of Canada.
High performance glazing options include; ‘self-cleaning’ glass, spectrally selective daylighting glass, tinted glass, reflective glass, Heat Mirror ™, pyrolitic (hard coat) low emissivity glass, and sputtered (soft coat) low emissivity glass, as well as standard safety glass options.
Back to
the Top
GLAZING
The glass sits on shims and is held in place by a removable exterior aluminium glass stop. Double sided foam tape on the interior and a thermoplastic rubber gasket on the exterior assist in securing the glass. The glazing cavity is edge drained to the exterior with concealed drainage holes. The glazing cavity is also edge vented to the exterior through concealed vent holes. The glass replacement does not require sash replacement.
Back to
the Top
MUNTINS
Muntin options include Georgian grilles between glass and two types of simulated divided lites in both double and triple glazing.
Back to
the Top
WEATHERSTRIPPING
The three seal design conforms to the rain screen principle. The exterior seal prevents dust and rain penetration. The centre thermoplastic bulb seal prevents air leakage. The inner thermoplastic seal restricts air from circulating into the hardware cavity and condensing on the sash and on the hardware. All weatherstripping is replaceable.
Back to
the Top
SCREEN
Factory installed screens come with all opening windows. The roll formed aluminium screen frame is held in place with 4 retractable retaining pins, concealed in the screen’s corner keys. Screen frames are white or beige and are recessed mounted in the frames. Standard screens are made from black, non-glare, fiberglass cloth, which is spline set.
Our continuous improvement policy means that we may, without notice, change our specifications at any time.
Casement Windows
Features • Product Description • Thermal Performance
Available Sizes
• Vertical Section
• Horizontal Section • Mullion
details
Photo Gallery
Choose another style of
window/door:
Back to
the Top
Home
Contact Us Search
Why Thermotech Consumer's
Guide Products
Links Stephen's
Column Copyright
© 2010 by Thermotech Fiberglass Fenestration Ltd.
Telephone:
1-888-930-9445 Facsimile:
613-839-9066 Website
design and layout by 2Design Web
|
